Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Tsuru, Daigo; Sakurai, Shinji; Nakamura, Shigetoshi; Ozaki, Hidetsugu; Seki, Yohji; Yokoyama, Kenji; Suzuki, Satoshi
Fusion Engineering and Design, 98-99, p.1403 - 1406, 2015/10
Times Cited Count：3 Percentile：25.85(Nuclear Science & Technology)Ezato, Koichiro; Suzuki, Satoshi; Seki, Yohji; Mori, Kensuke; Yokoyama, Kenji; Escourbiac, F.*; Hirai, Takeshi*; Kuznetsov, V.*
Fusion Engineering and Design, 98-99, p.1281 - 1284, 2015/10
Times Cited Count：40 Percentile：95.98(Nuclear Science & Technology)Japan Atomic Energy Agency (JAEA) is now devoting to development of Full-W ITER divertor outer vertical target (OVT), especially, PFU that needs to withstand the repetitive heat load as high as 20MW/m
. JAEA have succeeded in demonstrating that the soundness of a bonding technology is sufficient for the full-W ITER divertor. For the development of bonding technology, the load carrying capability test on the W monoblock with a leg attachment to an OVT support structure was carried out and shows that the attachment can withstand against the uniaxial load more than 20 kN which is three times higher than the IO requirement. JAEA manufactured 6 small-scale mock-ups and tested under the repetitive heat load of 10 and 20 MW/m to examine the durability of the divertor structure including W tile bonding and the cooling tube. All of the mock-ups could survived 5000 cycles at 10 MW/m and 1000 cycles 20 MW/m with no failure such as debonding of the W tile and water leak from the cooling tube. The number of cycles at 20 MW/m is three times longer than the requirement of ITER divertor.
Ezato, Koichiro; Dairaku, Masayuki; Taniguchi, Masaki; Sato, Kazuyoshi; Suzuki, Satoshi; Akiba, Masato; Ibbott, C.*; Tivey, R.*
Fusion Science and Technology, 46(4), p.530 - 540, 2004/12
Times Cited Count：14 Percentile：66.09(Nuclear Science & Technology)The first fabrication and heating test of a large-scale CFC monoblock divertor mock-up using annular flow concept have been performed to demonstrate its manufacturability and thermo-mechanical performance. Prior to the fabrication of the mock-up, brazed joint tests between the CFC monoblock and the CuCrZr tube have been carried out to find the suitable heat treatment mitigating loss of the high mechanical strength of the CuCrZr material. Basic mechanical examination on CuCrZr undergoing the brazing heat treatment and FEM analyses are also performed to support the design of the mock-up. High heat flux tests on the large-scale divertor mock-up have been performed in an ion beam facility. The mock-up has successfully withstood more than 1,000 thermal cycles of 
for 15 s and 3,000 cycles more than 
for 15 s, which simulates the heat load condition of the ITER divertor. No degradation of the thermal performance of the mock-up has been observed throughout the thermal cycle test.
Ezato, Koichiro; Suzuki, Satoshi; Sato, Kazuyoshi; Akiba, Masato
Journal of Nuclear Materials, 329-333(1), p.820 - 824, 2004/08
Times Cited Count：6 Percentile：40.72(Materials Science, Multidisciplinary)This paper presents thermal fatigue experiments of a cooling tube with a helical triangular fin on its inner cooled surface, namely a 
. The screw thread is directly shaped in a CuCrZr heat sink bar as a cooling channel. Slits with the width of 1.5 mm are machined at the heated side of the heat sink. The thermal fatigue experiments are carried out at 20 and 30 
by using an electron beam irradiation facility in JAERI. Water leakages from fatigue cracks, which locate at the slit of the heat sink, occurred at around 4500th and 1400th cycles at 20 and 30 , respectively. These results show good agreement with lifetime predictions using Manson-Coffin's law based on finite element analyses. Fractographic observations reveal that the fatigue cracks start from the outer heated surface at the slit region of the cooling channel and propagate toward its inner surface.
Akiba, Masato; Ishitsuka, Etsuo; Enoeda, Mikio; Nishitani, Takeo; Konishi, Satoshi
Purazuma, Kaku Yugo Gakkai-Shi, 79(9), p.929 - 934, 2003/09
no abstracts in English
Hatano, Toshihisa; Enoeda, Mikio; Kuroda, Toshimasa*; Akiba, Masato
JAERI-Tech 2002-075, 59 Pages, 2002/10
JAERI-Tech-2002-075.pdf:17.38MB
no abstracts in English
Sato, Satoshi; Hatano, Toshihisa; Furuya, Kazuyuki; Kuroda, Toshimasa*; Enoeda, Mikio; Takatsu, Hideyuki
JAERI-Research 97-092, 80 Pages, 1998/01
JAERI-Research-97-092.pdf:5.11MB
no abstracts in English
Hatano, Toshihisa; ; ; *; *; Kitamura, Kazunori*; Kuroda, Toshimasa*; Akiba, Masato; Takatsu, Hideyuki
Fusion Engineering and Design, 39-40, p.363 - 370, 1998/00
Times Cited Count：20 Percentile：81.49(Nuclear Science & Technology)no abstracts in English
Akiba, Masato; Tanaka, Shigeru; Seki, Masahiro
Nihon Genshiryoku Gakkai-Shi, 33(5), p.447 - 454, 1991/05
Times Cited Count：2 Percentile：31.89(Nuclear Science & Technology)no abstracts in English
Tsuru, Daigo; Sakurai, Shinji; Nakamura, Shigetoshi; Ozaki, Hidetsugu; Seki, Yohji; Yokoyama, Kenji; Suzuki, Satoshi
no journal, ,
no abstracts in English
Ezato, Koichiro; Seki, Yohji; Suzuki, Satoshi; Yokoyama, Kenji; Yamada, Hirokazu; Hirayama, Tomoyuki
no journal, ,
no abstracts in English
